Showing results: 916 - 930 of 1099 items found.
-
PCCextend 120 HIB -
Sycard Technology
For those applications that require access to the 16-bit PC Card interface that can't use a standard extender card, Sycard provides the PCCextend 120 HIB (Host Interface Board) which allows full access to all 68-signal and power pins on the PC Card host. Standard 0.1" headers allow the user to connect standard 34-pin ribbon cable to test or prototype hardware.
-
BT-QAM-PRO -
Blonder Tongue Laboratories, Inc.
The BT-QAM-PRO is an economical feature-packed test instrument for analyzing CATV QAM and Broadcast 8VSB digital channels, as well as NTSC analog channels. This compact instrument is designed with field service technicians in mind and provides many of the features that are typically only found in many higher-priced units. The BT-QAM-PRO comes complete with a soft water-resistant case and a micro USB charging/PC cable.
-
TX2001 -
BI Communications
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Video Products Inc
CCTV Tester with Power Over Ethernet (PoE) and IP Testing is a portable, multifunction tester for CCTV installations and maintenance. Power cameras and review the display without the hassle of running between the camera and a DVR located in a separate area. Test options include: audio, video, ping, TDR, PoE, IP network connections, and LAN (local area network) cable connections.
-
ECAD System 2002 -
CM Technologies Inc.
The ECAD System 2002 is a portable, ruggedized tester that can be used for troubleshooting and condition monitoring of installed circuits, cables and wiring harness. The ECAD tester is a combination of traditional electrical measurements, a database for storing test results, and data analysis software. This powerful combination allows a user to evaluate the condition of all circuit components in a logical and straightforward manner from one end of the circuit.
-
280 Series -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 280 HDMI/HDBaseT Video Generator (Tx) and Analyzer (Rx) is small compact, battery powered test set ideally suited for professional A/V integrators and home theatre installers. This convenient test set enables you to conduct basic verification and diagnostic tests on HDMI/HDBaseT cables, video distribution networks and individual A/V components. The HDMI input and output ports support testing up to 18 Gbps data rate and 600 MHz pixel rate and the HDBaseT input and output ports support testing up to 300 MHz pixel rate. The HDBaseT interface supports transmission in Long Reach mode as well.
-
SCHILLER AUTOMATION GmbH & Co. KG
The Standard SD Express Memory Card Test Adapters support PCIe® 16 GT/s (Gen4) and PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD8.0 and SD7.1. Minimal crosstalk, short trace lengths. The Micro SD Express Memory Card Test Adapters supports PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD7.1. Minimal crosstalk, short trace lengths. They all support SDHC, SDXC, and SDUC operation modes Data collection via Lab Standard SSMP Test Cables and hard gold mating surface allow for high cycle count insertions and reliable performance.
-
DMC, Inc.
Automated test systems may be as simple as a laptop with a DAQ module or a stand-alone controller, but they typically require a mix of off-the-shelf and custom hardware. All that hardware is integrated and wired into a test stand. Portable or mobile test stands are ideal for in-the-field research and development and servicing of multiple laboratories or manufacturing lines. Test stand access to the front panels of hardware and subcomponents allows manual configuration of non-automated settings. Quick disconnects, cable harnesses, and easy access to probes provides efficient setup and tear-down. Expandable or modular rack mount and card base systems facilitate future needs. Ergonomic considerations include keyboard and display placement, along with number of monintors. Safety is always crucial with proper E-stop placement and keeping dangerous elements away from users.
-
PLTM20 -
Pyle Audio Inc.
Tests Pin Configuration for 10 Base-T, 10 Base-2, RJ45/RJ11, 356A, TIA-569A/568B and Token Ring CableRemotely Test Cables Up to 330 Yards AwayTest Ground WireMeasure DC/AC Voltage, DC/AC Current, Resistance, Continuity, and DiodeDC Voltage: Max Range 600 V, Accuracy +/- 0.5%AC Voltage: Max Range 600 V, Accuracy +/- 1.2%DC Current: Max Range 200 mA, Accuracy +/- 1.2%AC Current: Max Range 200 mA, Accuracy +/- 2.0%Resistance: Max Range 20 M, Accuracy +/- 0.8%Continuity Test: Beeps If Less Than 100 Accessories Included: Test Leads, LANtest Remote Terminator, 9V Battery, Carrying CaseDimensions: 6.38' H x 2.93' W x 1.73' DWeight: 10.86 oz.Sold as : Unit
-
M8K708 -
Excalibur Systems, Inc.
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Teledyne Defense Electronics Storm Microwave
Storm Products has been producing high performance semi-rigid interconnects for over 20 years for a variety of markets, including: defense, telecom, wireless and test & measurement. Experienced in:- Cable sizes from 0.034" to 0.500"- Solid PTFE dielectric and high performance tape wrapped products- Wide variety of standard connector styles: MCX, SMA, SMB, SMC, TNC, N, 7/16, SC, and HN- Years of experience on blindmate connector styles: OSP GPO, GPPO, and GMSSpecialized experience in:- Applications where phase stability is critical- low intermod interconnects- High power designsManufacturing equipment:- Automated bending equipment and optical comparators - Programmable thermal chambers for pre-conditioning formed cables- Specialized assembly and soldering equipment for high volume applications- Automated network analyzers through 50GhzDue to the custom nature of formed semi-rigid cable assemblies, additional information is required before providing a quotation for your requirement.
-
PRS-812B -
Prostat Corporation
- Wide Range Resistance: 0.10 Ω to 1.00x1012 Ω- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Constant Test voltages 10V and 100V for specification measurements to meet international and domestic ESD measurement standards- Auto Resistance Range Control- Auto Test Voltage Control- Uses a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- 120 Data Set Internal Memory- Uses Standard USB Cable for Charging- Charges in 2 Hours- 2-year Limited Warranty on Main Instrument
-
ESD MANUFACTURING & SUPPLY
The ESD LCD SURFACE RESISTIVITY METER provides everything necessary to test work surfaces using the procedure outlined in the EOS/ESD-S4.1 standard. This test kit makes testing surface resistance easy – simply place the weights attach the cables, switch to the correct voltage and press the button to read resistance directly on the meter. The meter incorporates parallel probes on the bottom of the unit which allows the user to make surface resistivity measurements. The parallel probes allow for quick and easy testing of a variety of surfaces and materials, without the use of the five pound electrodes
-
JW3327 -
Shanghai Joinwit optoelectronic Tech,co.,Ltd
JW3327 Insertion/Return Loss Test Station is a Joinwit precise instrument, which be adopted advantages from current abroad instrument brand and improved to the application from clients, developed by Joinwit. It is a technological breakthrough in the domestic market and greatly improves the efficiency of IL test of optical devices to the MM with two wavelengths testing result in one station. It has extensive applications in the fiber cable, fiber passive device, fiber active device and optical communication system. It is suitable to perform the WIP testing and sample character testing for fiber device manufacturer research institutes.
-
CSW Series -
AMETEK Programmable Power, Inc.
The CSW Series represents a new generation of AC/DC power sources that address the increasing demands on test equipment to perform additional functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the Compact CSW Series is capable of handling complex applications that have traditionally required multiple systems. The sleek integrated approach of the CSW avoids cable clutter that is commonly found in test systems. All connections are made internally and the need for digital multimeters, power harmonics analyzers, and current shunts or clamps is eliminated.
